How To Mow Wet Grass

Tips On How To Cut Wet Grass

The first thing to keep in mind is that electricity and water do not mix. You run the risk of getting an electric shock if you try to use an electric lawn mower to mow wet grass – particularly if you are using an extension cord. If the connections (along with the wiring right under the damaged or worn parts of the cord) get exposed to any moisture, then that can damage the machine and you could be electrocuted. No matter what type of engine your motor has, there are potential personal dangers when mowing wet grass. Simply walking across a slick lawn with sufficient force to help you push the mower may cause you to slip and then fall down close to the blades on the mower. It can be difficult trying to mow a wet lawn. Wet blades of grass are slick and hard to slice, which creates – at best – an uneven shred instead of a clean-cut that you can achieve on a sunny day. Unless the blades on your mower are in peak condition, or newly replaced or sharpened, it might take several passes going over the same patches of wet lawn to mow even a small fraction of what you could cut when the lawn is dry. Another option is to hire a grass cutting company to do the work for you. Keep reading for some helpful tips on how to safely and properly mow your lawn. Houston Landscaping Source is the top grass cutting company for all of your lawn care needs.

1. Clean Up After You Mow

When there are damp grass clippings clinging to the underside of the mower deck on your lawn mower it forms a soggy layer of material that can turn quickly into the mold. If there is a washout port on your mower, then definitely use it for cleaning the deck. However, even when you are done mowing, use a putty knife to scrape the deck to clean. Make sure to clean the lip in the area where the edge of the deck curls underneath. (The same is true for a string trimmer. The debris shield should be cleaned after each trimming.) Also, use a wire brush to clean the tires on your mower. Finally, to get rid of the wet clippings, wipe the top part of the mower down, and to remove air fill up the gas tank. If you find that you do not want to go through the struggle of mowing wet grass then turn to the #1 grass cutting company to take care of your lawn.

2. Mow More Frequently

If you tend to mow every seven days, cut them down to every five days or less. That will help to prevent your grass from getting too shaggy and long. It is hard to cut tall grass, and wet, tall grass is even harder to mow.

3. Raise Your Mower Deck

A majority of grasses in the country’s damp area are cool-season grasses. They grow the best having a 3 to 4-inch long leaf. However, most homeowners cut these types of grasses much too short. Damp mowing conditions magnify the problem. The mower is unable to handle this. Raise the mower deck to either the second-highest or highest setting and always use it.

4. Side-Discharge, When Everything Else Fails

In really bad conditions, instead of mulching or bagging, side-discharge instead. Set your mower on its highest setting, and the side discharge and then mow. Of course, that will leave behind rows of grass clippings on your lawn. One thing you can do is cross-mow (mowing at 90 degrees on the first mow) in bagging or mulching mow to get rid of the clippings; or you can rake them up or allow them to dry for a few days and then mow again, in bagging or mulching mode this time.

5. Manage Your Fuel

Each time you fill the gas can for your mower, use stabilizer, and make sure to not purchase any more fuel than you can use in a two or three week period. The ethanol in gas is attracted to moisture. When you stabilize the fuel and go through your supply of fuel as soon as you can it will help to prevent fuel contamination from occurring.

6. Sharpen Your Mower Blades

A crisp cut is produced by a sharp blade and helps to keep your grass healthy. It is especially important when you have damp mowing conditions since the blade will tend to shred instead of cut the grass.

Contact A Grass Cutting Company

Cutting the grass doesn’t mean your work is over. Extra cleanup is required when you have wet grass since grass clippings will tend to cling more when there is water involved. Damp grass clippings sticking to the undercarriage of your mower can create a great environment for mold to breed – and a broken mower eventually – if the machine stays too wet for too long. Make sure to clean the deck and blades and also wipe the body of your mower down and brush the tires off as well. You also need to pay attention to any stains. Chlorophyll from newly cut wet grass can cause more stains that on a dry mowing day, so you will need to remove the grass stains right away from your driveway, shoes, and clothes. Houston Landscaping Source is the top-rated lawn care company reading to care for your lawn. Cutting wet grass can be a stressful process of lawn care but we are here to help you. Call a professional today at (281) 994-9844.


Your email address will not be published.Required fields are marked *

Leave a reply